Skip to main content

v2.1

Minor Versionm

by Alkesh Dhak

    • WARNING! Only use Geotab telematics devices with Geotab-approved harnesses acquired from Geotab-authorized channels. Use of non-Geotab harnesses from unauthorized channels can cause serious safety risks, including fire, and can lead to serious personal injury and/or damage to the vehicle.

    • IMPORTANT: Always use a vehicle-specific harness when offered by Geotab or the vehicle manufacturer to avoid possible GO device damage. Some vehicles have multiple diagnostic connectors to choose from when installing a GO device.

    • For more information on Geotab harnesses and adapters, see Harness Identification and Application & Harness Assessment Cheat Sheet GUIDE V2.0

    • If a longer length is required to facilitate installation, connect a straight harness to a T-harness. Ensure that the total harness length does not exceed 2 meters (or 6.5 feet). Any two harnesses that exceed 2 meters may compromise the integrity of the data and cause issues with the vehicle’s Engine Control Unit (ECU).

    • For more details on compliance information and applicable products, contact your Authorized Reseller.

    • Some installations are not straightforward and must be completed by an Authorized Installer to ensure a secure installation.

    • Ensure to use many cable ties to secure both the device and harness to the vehicle. An unsecure device installation can result in poor electric and/or data connections that can lead to short circuits and fires or cause malfunctions of vehicle controls that can result in serious personal injury or significant damage to your vehicle.

    • Some examples requiring professional installation from an Authorized Installer are:

    • The OBD port location is such that the device could protrude or interfere when entering or exiting the vehicle, or located where it can be inadvertently kicked or bumped during vehicle operation. The device isn't fully secured and so may be able to vibrate loose or get kicked or knocked. An electrical harness or additional wiring is required.

    • Vehicle mounting modifications are required to secure the device i.e. removing of panels, or the OBD connector has been deformed/damaged or there is any physical damage visible to the electrical wiring.

    • The device does not power on and beep six times when first installed.

    • The installer questions their ability to complete a secure installation according to these instructions.

    • Do not attempt to install, reconfigure or remove any product from a vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked.

    • Attempting to service devices while the vehicle is in motion could result in malfunctions or accidents, leading to death or serious personal injury.

  1. Before installing, you should record the following:
    • Before installing, you should record the following:

    • GO device serial number

    • Found above barcode on device label

    • Odometer

    • Fleet Alias/Number/ID

    • VIN (vehicle identification number)

  2. Remove the center console top and side covers.
    • Remove the center console top and side covers.

    • Top is usually secured with (4) T25 screws at the corners.

    • Side is usually secured with (4) T25 screws also at the corners.

  3. In the center console locate the following:
    • In the center console locate the following:

    • Twisted yellow and green J1939 wires.

    • Power bus bar.

  4. Prepare the HRN-CE10K2 kit:
    • Prepare the HRN-CE10K2 kit:

    • Take the HRN-CE10K2 harness and cut the black and red wires that lead to the black power connector.

    • Using the parts provided in the HRN-5AFUSEKIT, add a butt connector, fuse holder and ring terminal to the RED wire and a ring terminal only to the BLACK wire.

  5. Using a DMM, identify, verify,  & connect to the following:
    • Using a DMM, identify, verify, & connect to the following:

    • +12 volt (constant) source.

    • Ground source.

    • Connect the fused RED wire to the +12V post and the BLACK wire to the ground post on the power bus bar.

  6. Connect the white 6-pin connector labeled OBD2  from the HRN-CM24Y1 with the mating white 6-pin  connector labeled OBD2 from the HRN-CE10K2.
    • Connect the white 6-pin connector labeled OBD2 from the HRN-CM24Y1 with the mating white 6-pin connector labeled OBD2 from the HRN-CE10K2.

  7. Remove the terminating resistor from the green and yellow twisted pair connector labeled MCJ1939-2. Reinstall the terminating resistor into the mating end of the HRN-CE10K2.
    • Remove the terminating resistor from the green and yellow twisted pair connector labeled MCJ1939-2.

    • Reinstall the terminating resistor into the mating end of the HRN-CE10K2.

    • Connect the HRN-CE10K2 to the mating connector where the terminating resistor was removed from MCJ1939-2.

  8. Connect the HRN-CM24Y1 to the GO device and secure the connection with a cable tie. Use two additional cable ties to secure the GO device inside the center console.
    • Connect the HRN-CM24Y1 to the GO device and secure the connection with a cable tie. Use two additional cable ties to secure the GO device inside the center console.

    • If installing an IOX accessory please continue using the correct guide from here.

  9. Start Vehicle.
    • Start Vehicle.

    • Verify LED pattern.

    • The device emits 2 quick beeps every 60 seconds during set-up. Once all three LEDs turn solid and you hear 10 quick beeps.

    • All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, airbags, and gas, brake and clutch pedals.

    • This requires the use of a cable tie when securing the device or any extension harness to the OBD connector, securing both sides of the harness. If you do not use a cable tie, vibration in the vehicle can lead to a loose connection which could cause the vehicle’s engine computer to fail, causing potential loss of vehicle control and serious injury.

    • Inspect devices and cabling regularly to ensure all devices and cabling continue to be securely attached.

    • If at any point after an in-vehicle device is installed a warning light illuminates on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.

  10. Enter the installer information.
    • Enter the installer information.

  11. Enter the device serial number.
    • Enter the device serial number.

    • If possible, use the barcode scan feature.

  12. Turn on the vehicle and wait for the device status to PASS. Some Hybrids and EV's may require a short drive
    • Turn on the vehicle and wait for the device status to PASS.

    • Some Hybrids and EV's may require a short drive

    • If the device status shows as FAILED, verify the LED status and turn the vehicle engine off and on again.

    • Press Refresh to check the status again.

    • Refer to this link for detailed instructions.

  13. Enter all applicable vehicle information.
    • Enter all applicable vehicle information.

    • Enter applicable Camera information in the Camera ID field if one was installed.

    • Read and acknowledge Geotab's Privacy policy.

  14. If the installation check finishes without errors, a Success! message appears. Press New installation to check another installation, or press Exit when done.
    • If the installation check finishes without errors, a Success! message appears.

    • Press New installation to check another installation, or press Exit when done.

    • If the installation check encounters any errors, an Error message appears.

    • Select New installation to check another installation or press Exit when done.

    • For the latest version of the Limitations of Use, please visit: http://goo.gl/k6Fp0w

    • Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants. Failure to do so may result in units malfunctioning or short-circuiting, which can lead to a fire hazard and cause loss or serious injury.

    • Do not attempt to remove the devices from the vehicle in which they are originally installed for installation in another vehicle.

    • Not all vehicles share compatibility, and doing so may result in unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s engine while in operation or cause your vehicle to operate poorly or erratically and cause serious injury and/or vehicle damage.

    • This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. Unauthorized servicing of these products will void your product warranty.

    • The simplified EU declaration of conformity referred to in Article 10(9) shall be provided as follows:

    • Hereby, Geotab (Address: 2440 Winston Park Drive, Oakville, Ontario L6H 7V2, Canada, Phone number: 1 (877) 436-8221) declares that the radio equipment type ‘telematics device’ is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available here.

    • WARNING: Cancer and Reproductive Harm

Finish Line

Alkesh Dhak

Member since: 04/07/2022

59 Guides authored

Team